skydiverek 56 #1 August 29, 2008 When relining the canopy, is the removed lineset destroyed in the process (i.e. cut, made unusable, etc.)? Or can you take it and install it on a different canopy (providing it still has some life left, of course)? Quote Share this post Link to post Share on other sites
PhreeZone 15 #2 August 29, 2008 The lines are cut to remove it from the canopy.Yesterday is history And tomorrow is a mystery Parachutemanuals.com Quote Share this post Link to post Share on other sites
monkycndo 0 #3 August 29, 2008 If the lines are not cascaded, they can be removed without cutting.50 donations so far. Give it a try. You know you want to spank it Jump an Infinity Quote Share this post Link to post Share on other sites
NickDG 23 #4 August 29, 2008 I remember when I was a kid my mom would give me a quarter and send me down to the neighborhood shoemaker for new shoelaces. He'd pick me up and place me in the big chair. But he'd never undo my laces, he'd pull out a big honking pair of shears (that scared the crap out of me) and just sliced them off in one swipe. Riggers are the same as shoemakers . . . NickD Quote Share this post Link to post Share on other sites
ficus 0 #5 August 29, 2008 The way I do it, it is. Quote Share this post Link to post Share on other sites
darkwing 4 #6 August 29, 2008 If they are cascaded (as most are), they most certainly do not HAVE to be destroyed in the removal process, but it takes a lot more time (thus money) to remove them that way. Talk to your rigger if you think you want to save them. As a rigger I'd say it would be pretty unusual for it to be worth the hassle of saving a set, but I suppose it is possible that it would be worth it. -- Jeff My Skydiving History Quote Share this post Link to post Share on other sites
RIGGER 0 #7 August 30, 2008 When a canopy is relined that means`that the removed lines set is out of service & should not be used anymore. Be Safe !!! Quote Share this post Link to post Share on other sites
popsjumper 2 #8 August 30, 2008 Quote As a rigger I'd say it would be pretty unusual for it to be worth the hassle of saving a set, but I suppose it is possible that it would be worth it. Yes, I could save them if I wanted to remove bar tacks...but that will cost you...dearly...more than the new line set costs. Do the math. I would question the safety of re-using them given the damage done by removing and re-tacking them.My reality and yours are quite different. I think we're all Bozos on this bus. Falcon5232, SCS8170, SCSA353, POPS9398, DS239 Quote Share this post Link to post Share on other sites
base283 0 #9 August 30, 2008 Quote I would question the safety of re-using them given the damage done by removing and re-tacking them. Should not be a prob if one knows how to de-bartack without damage (slide a needle under the stitching and use a razor blade to shave off the topside). But it would be like a rigging art masterpiece to do this on an entire lineset. Hours of painstaking work. Only to have the Jumper go and jump those dang lines after all the hard work. Sacrilege I tell ya, Sacrilege. Take care, space Quote Share this post Link to post Share on other sites
DougH 270 #10 August 30, 2008 That is a good trick, thanks for posting that, I will keep that in mind! "The restraining order says you're only allowed to touch me in freefall" =P Quote Share this post Link to post Share on other sites
base283 0 #11 September 1, 2008 I got it from Stane at Atair. Take care, space Quote Share this post Link to post Share on other sites
Broke 0 #12 September 1, 2008 Why not just use a seam ripper to remove the old bar tack?Divot your source for all things Hillbilly. Anvil Brother 84 SCR 14192 Quote Share this post Link to post Share on other sites
DougH 270 #13 September 2, 2008 Jason, I have used a seam ripper to take the bartack out of lower control lines. It is a PITA when the bartack is on a line. Just my personal opinion, this shave technique sounds way less labor intensive. I am definetly going to try it next time. BTW, I have been rationing and savoring that beer. "The restraining order says you're only allowed to touch me in freefall" =P Quote Share this post Link to post Share on other sites
base283 0 #14 September 2, 2008 Seam rippers are designed to take seams out. Even the smallest of mine are bigger than a medium size lightweight needle and are not very handy for taking out bartacks. With a needle, one can work it thought the bar tack without catching any line fibers and then shave them off. If the bartack is deep into the line, you can use the eye end of the needle to slip it under. Take care, space Quote Share this post Link to post Share on other sites
masterrigger1 2 #15 September 3, 2008 Quote Seam rippers are designed to take seams out. Even the smallest of mine are bigger than a medium size lightweight needle and are not very handy for taking out bartacks. The small ones from Wal-Mart are great for removing bartacks. They are made by Prym. I use then all the time here in the shop with great results. BS, MELSkyworks Parachute Service, LLC www.Skyworksparachuteservice.com Quote Share this post Link to post Share on other sites