Copycat 0 #1 February 2, 2008 I've finally finished assembling my rig 2 weeks ago, mounted the main on the risers with new slinks and away it went for a reserve repack. I asked my rigger (first time i'm dealing with this one) to give it a quick check because I saw small holes in my canopy. After a week he sent me an email saying that to repair the canopy would cost me around 600$! I had payed less for the canopy itself! He said there were 8 holes and 6 lines needed to be changed. I got the canopy used but the condition was above OK in my eyes and I quite trust the guy that sold me. I said to him to nevermind, I'd jump it anyway. The rig came with a soft reserve and a yellow cutaway handle (Jav TJN). I didn't like any so I swapped them with my old Reflex' (after double checking the lenghts were the same, the difference was 5mm at the most). He also added this to the price (whooping 200$) because he said I can't use "other rig handles" I said to him I had the originals anyway. So, what do you think? I changed rigger because the last one took ages for a repack (but she did a good job), but I'm guessing this one is just trying to rip me off in any way he can... Any comments / questions / ideas very welcome! Blue skies from Italy, -Patrik Quote Share this post Link to post Share on other sites
NWFlyer 2 #2 February 2, 2008 QuoteI had payed less for the canopy itself! He said there were 8 holes and 6 lines needed to be changed. I got the canopy used but the condition was above OK in my eyes and I quite trust the guy that sold me. I said to him to nevermind, I'd jump it anyway. Are you a rigger? Is the guy who sold it to you a rigger? Lines may "look fine" but need to be replaced if they are out of trim. If you don't trust the rigger who's looking at it for you, by all means get a second opinion from another rigger, but if it were me I wouldn't just go out and jump it after a recommendation like that unless I also had the skill set to make the evaluation of the condition of the rig. But if I also had the skill set to make the evaluation of the rig, I wouldn't have sent it off to someone else for a repack. So I'm guessing you don't."There is only one basic human right, the right to do as you damn well please. And with it comes the only basic human duty, the duty to take the consequences." -P.J. O'Rourke Quote Share this post Link to post Share on other sites
MajorDad 0 #3 February 2, 2008 Quote I've finally finished assembling my rig 2 weeks ago, mounted the main on the risers with new slinks and away it went for a reserve repack. I asked my rigger (first time i'm dealing with this one) to give it a quick check because I saw small holes in my canopy. After a week he sent me an email saying that to repair the canopy would cost me around 600$! I had payed less for the canopy itself! He said there were 8 holes and 6 lines needed to be changed. I got the canopy used but the condition was above OK in my eyes and I quite trust the guy that sold me. I said to him to nevermind, I'd jump it anyway. The rig came with a soft reserve and a yellow cutaway handle (Jav TJN). I didn't like any so I swapped them with my old Reflex' (after double checking the lenghts were the same, the difference was 5mm at the most). He also added this to the price (whooping 200$) because he said I can't use "other rig handles" I said to him I had the originals anyway. So, what do you think? I changed rigger because the last one took ages for a repack (but she did a good job), but I'm guessing this one is just trying to rip me off in any way he can... Any comments / questions / ideas very welcome! Blue skies from Italy, -Patrik Looking at your other posts, you sure do get scammed a lot. Assuming this isnt a troll, you may want to talk to riggers/senior jumpers you know and trust before buying second hand gear. If it is a troll, go on and jump the parachute. Major Dad CSPA D-579 Quote Share this post Link to post Share on other sites
monkycndo 0 #4 February 2, 2008 Let's see, 90 jumps Wing loading at 1.3 on main and 1.5 on reserve Questioning a rigger with that vast experience verses the friend you "trust" I say either here's my cash to enter bounce bingo on Copycat or Trollin', trollin', trollin', keep the BS posts a rollin', Troll hide.50 donations so far. Give it a try. You know you want to spank it Jump an Infinity Quote Share this post Link to post Share on other sites
likestojump 3 #5 February 2, 2008 Quote I said to him to nevermind, I'd jump it anyway. The rig came with a soft reserve and a yellow cutaway handle (Jav TJN). I didn't like any so I swapped them with my old Reflex' (after double checking the lenghts were the same, the difference was 5mm at the most). He also added this to the price (whooping 200$) because he said I can't use "other rig handles" I said to him I had the originals anyway. you're a good guy to start bounce bingo on. any TSO'd parts (Such as the reserve handle) MUST be original manufacturer, And if I understand you correctly, you telling him the Reflex handles you provided with the JAvelin were originals - that's plain wrong. Keep in mind I go by FAA rules here in the US, but the MANUFACTURER is the one that says not to change any auxilary components without their knowledge/approval. bounce bingo anybody ? Quote Share this post Link to post Share on other sites
riggerrob 558 #6 February 3, 2008 QuoteQuote I said to him to nevermind, I'd jump it anyway. The rig came with a soft reserve and a yellow cutaway handle (Jav TJN). I didn't like any so I swapped them with my old Reflex' (after double checking the lenghts were the same, the difference was 5mm at the most). He also added this to the price (whooping 200$) because he said I can't use "other rig handles" I said to him I had the originals anyway. you're a good guy to start bounce bingo on. any TSO'd parts (Such as the reserve handle) MUST be original manufacturer, And if I understand you correctly, you telling him the Reflex handles you provided with the JAvelin were originals - that's plain wrong. Keep in mind I go by FAA rules here in the US, but the MANUFACTURER is the one that says not to change any auxilary components without their knowledge/approval. bounce bingo anybody ? >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> I am going to disagree with you. FAA Master Riggers are allowed to swap similar TSOed components. Since swapping ripcord handles may involve complex questions about compatibility, the job is best left to a Master Rigger. Quote Share this post Link to post Share on other sites
mark 102 #7 February 3, 2008 QuoteFAA Master Riggers are allowed to swap similar TSOed components. AC 105-2C para 11 says that riggers (presumably including senior riggers) may assemble approved components from different manufacturers, "in accordance with the manufacturer's instructions." Javelin instructions require use of Sunpath-produced ripcords, so even though we might be allowed to substitute parts in general, in this specific case it is not allowed. It isn't necessarily a question of safety, just legality. Mark Quote Share this post Link to post Share on other sites
pilotdave 0 #8 February 3, 2008 His profile says he's from Italy, so I'm not sure there's a legality problem unless they have a similar rule there. But anyway, ACs aren't legally binding documents, are they? Dave Quote Share this post Link to post Share on other sites
riggerrob 558 #9 February 3, 2008 Since Italy is within the European Union and the EU adopted JTSO/ETSO several years ago, we can assume that Italian riggers have to follow the same rules as American riggers. Yes, Eric Fradet has hinted at the political nightmare of standardizing rigger ratings across Europe. He said something about everyone fiercely protecting their privileges. Even if ACs were not legally binding documents, you would look like an idiot if it could be proved that you disobeyed an AC. IOW The rigger who ignored an AC would be "on his own" in court. At a minimum, ACs are "good practice." Quote Share this post Link to post Share on other sites
likestojump 3 #10 February 3, 2008 QuoteQuoteQuote I said to him to nevermind, I'd jump it anyway. The rig came with a soft reserve and a yellow cutaway handle (Jav TJN). I didn't like any so I swapped them with my old Reflex' (after double checking the lenghts were the same, the difference was 5mm at the most). He also added this to the price (whooping 200$) because he said I can't use "other rig handles" I said to him I had the originals anyway. you're a good guy to start bounce bingo on. any TSO'd parts (Such as the reserve handle) MUST be original manufacturer, And if I understand you correctly, you telling him the Reflex handles you provided with the JAvelin were originals - that's plain wrong. Keep in mind I go by FAA rules here in the US, but the MANUFACTURER is the one that says not to change any auxilary components without their knowledge/approval. bounce bingo anybody ? >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> I am going to disagree with you. FAA Master Riggers are allowed to swap similar TSOed components. Since swapping ripcord handles may involve complex questions about compatibility, the job is best left to a Master Rigger. Rob, I wasn't clear, my last statement is exactly what you just stated. In other words I agree with what you said, you just said it better than me :) Quote Share this post Link to post Share on other sites
Copycat 0 #11 February 3, 2008 Hey, thanks for all the offenses, trolling accusations and whatnot. I just wanted to know what the difference between handles can really be ( I DO have the original SunPath handles, I just didn't like the soft ripcord and the yellow cutaway: My reflex' ones are metal and red, accordingly) And about the canopy, it was sold to me by a swedish master rigger, so what I see is a conflict of interests between both the riggers: the one selling me that it's in jumpable condition, the other one trying to scare me that if I don't cough up 600$ it might disintegrate on opening. And if I "get scammed a lot" is because I'm poor and I can't afford new equipment and buy directly from manufacturers or locally (prices in Italy are 60% higher and usually old PdF components) Apparently, "getting scammed a lot" is also just once, 2 years ago, by an american. Since then, I've avoided buying overseas and just stuck with Europe, mainly because of customs prices. QuoteJavelin instructions require use of Sunpath-produced ripcords, so even though we might be allowed to substitute parts in general, in this specific case it is not allowed. It isn't necessarily a question of safety, just legality. Mark Thanks for the reply. Do you have any online information regarding that? PS. I've attached the PDF document the rigger sent to me PS2: I've just realized that 453€ is more like $670 Quote Share this post Link to post Share on other sites
mark 102 #12 February 3, 2008 Quote QuoteJavelin instructions require use of Sunpath-produced ripcords, so even though we might be allowed to substitute parts in general, in this specific case it is not allowed. It isn't necessarily a question of safety, just legality. Mark Thanks for the reply. Do you have any online information regarding that? Javelin packing instructions are available as pdf download at Sunpath.com. 14 CFR (= U.S. FAA regulations) 65.129(e) requires packing, maintenance, and alterations to be done according to manufacturer instructions. Mark Quote Share this post Link to post Share on other sites
davelepka 4 #13 February 3, 2008 OK, here's your easy answer. Send your PD canopy to PD for repair/service work. They'll fix what needs fixing, and they'll do it right. Quote Share this post Link to post Share on other sites
riggerrob 558 #14 February 3, 2008 QuoteQuoteQuoteQuote I said to him to nevermind, I'd jump it anyway. The rig came with a soft reserve and a yellow cutaway handle (Jav TJN). I didn't like any so I swapped them with my old Reflex' (after double checking the lenghts were the same, the difference was 5mm at the most). He also added this to the price (whooping 200$) because he said I can't use "other rig handles" I said to him I had the originals anyway. you're a good guy to start bounce bingo on. any TSO'd parts (Such as the reserve handle) MUST be original manufacturer, And if I understand you correctly, you telling him the Reflex handles you provided with the JAvelin were originals - that's plain wrong. Keep in mind I go by FAA rules here in the US, but the MANUFACTURER is the one that says not to change any auxilary components without their knowledge/approval. bounce bingo anybody ? >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> I am going to disagree with you. FAA Master Riggers are allowed to swap similar TSOed components. Since swapping ripcord handles may involve complex questions about compatibility, the job is best left to a Master Rigger. Rob, I wasn't clear, my last statement is exactly what you just stated. In other words I agree with what you said, you just said it better than me :) >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> IIRC Standard Javelin (B and C yoke)ripcord is 17 inches from ball to top of pin. D or O yoke may require a different length. As for checking if it is a "similar TSO," the replacement ripcord should be stamped "TSO C23C" or "TSO C23D" along with something saying where and when it was made. Even if your Javelin was made under TSO C23C, it is possible to substitute a TSO C23D (later) ripcord because they have the same strength rating. Speaking of strength ratings, most Javelin reserve ripcords have a ball and shank/tube on the end ot ensure that they pass the 600 pound tensile test required when you install an RSL. Quote Share this post Link to post Share on other sites
Copycat 0 #15 February 3, 2008 Quote OK, here's your easy answer. Send your PD canopy to PD for repair/service work. They'll fix what needs fixing, and they'll do it right. I'd do it in a heartbeat... if I was in the US Quote IIRC Standard Javelin (B and C yoke)ripcord is 17 inches from ball to top of pin. D or O yoke may require a different length. As for checking if it is a "similar TSO," the replacement ripcord should be stamped "TSO C23C" or "TSO C23D" along with something saying where and when it was made. Even if your Javelin was made under TSO C23C, it is possible to substitute a TSO C23D (later) ripcord because they have the same strength rating. Speaking of strength ratings, most Javelin reserve ripcords have a ball and shank/tube on the end ot ensure that they pass the 600 pound tensile test required when you install an RSL. So if I use a same length ripcord, TSO'd (which it is, because it's from a Reflex) is OK? I really don't want to use the original one for safety reasons, because it's a soft handle. I don't want to go from a security concern to another. Quote Share this post Link to post Share on other sites
diablopilot 2 #16 February 3, 2008 TSO's are not general but rather specific to a rig. In other words, while your Reflex ripcord may be a acceptable replacement from a safety standpoint, it is not acceptable from a legal standpoint.---------------------------------------------- You're not as good as you think you are. Seriously. Quote Share this post Link to post Share on other sites
Copycat 0 #17 February 4, 2008 Thanks JP, I'd rather be an outlaw than feel unsafe every time on the way to altitude. To add to my dislike of soft handles, it's the exact same royal blue as my suit. I contacted my new rigger again today and asked him about the repairs, he said it was a courtesy full check and that's why he sent me the list with costs first before touching the canopy. He said that from a short time-span point of view, the canopy is very jumpable (even 100 jumps). He underlined that that costs were to leave it in absolute mint condition. Guess that it was just lack of good communication Sorry to seem like a troll, my only intention is to make this sport safer in any way, and learning about all the details I don't understand seems like a good first step. Olav always teaches me the importance of safety and not taking anything lightly. Blue skies everybody! Quote Share this post Link to post Share on other sites
riggerrob 558 #18 February 4, 2008 IIRC Standard Javelin (B and C yoke)ripcord is 17 inches from ball to top of pin. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Sorry, I meant to say 27 inches long. It is easy to check if a replacement ripcord is compatible. Start by trying to install the handle in its pocket. Next, slide the cable into the housing and finger-clamp the pin where it will be when the rig is packed. Check how much slack remains at the handle end. One inch is the minimum amount of slack, ... better if the ball end lays in the middle of the handle or near the bottom edge of a metal D handle. If the ball hangs much below the bottom edge of the handle, it increases the risk of an accidental deployment. Finally, the bottom end should have a ball and swage if your rig includes an RSL. Quote Share this post Link to post Share on other sites
JerryBaumchen 1,048 #19 February 4, 2008 Hi Rob, Quote better if the ball end lays in the middle of the handle or near the bottom edge of a metal D handle. Excellent, I can only hope people read, understand and follow this one. Quotethe bottom end should have a ball and swage if your rig includes an RSL. I think you mean ball & shank. JerryBaumchen Quote Share this post Link to post Share on other sites
Copycat 0 #20 February 4, 2008 QuoteIIRC Standard Javelin (B and C yoke)ripcord is 17 inches from ball to top of pin. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Sorry, I meant to say 27 inches long. It is easy to check if a replacement ripcord is compatible. Start by trying to install the handle in its pocket. Next, slide the cable into the housing and finger-clamp the pin where it will be when the rig is packed. Check how much slack remains at the handle end. One inch is the minimum amount of slack, ... better if the ball end lays in the middle of the handle or near the bottom edge of a metal D handle. If the ball hangs much below the bottom edge of the handle, it increases the risk of an accidental deployment. Finally, the bottom end should have a ball and swage if your rig includes an RSL. Check, check, and check! Thanks so much!! Quote Share this post Link to post Share on other sites
popsjumper 2 #21 February 5, 2008 QuoteThanks JP, I'd rather be an outlaw than feel unsafe.. I'll bet that NOT being an outlaw would let you feel even safer.My reality and yours are quite different. I think we're all Bozos on this bus. Falcon5232, SCS8170, SCSA353, POPS9398, DS239 Quote Share this post Link to post Share on other sites