sky490

I don't see the big deal. The photo they take is so degraded it's only good for Facebook

This was mounted on the rear door of one of our Skyvans. Keep in mind you must have any permanent mount inspected by the FAA. A grey area is tape mounts. They are not considered permanent

I happen to have over 200 jumps on this G2 with a Hero 3 Mounted onto the Cookie Pivot Point using my own design Quick Lock that works like a PL mount lens. I have had riser strikes but mostly I control the openings by forcing the risers wide during opening. I also jump a 119 Crossfire 2 with a wing loading of about 1:9 I do use a cut away system and the Quick Lock uses plastic screws like my Articulating Bracket

We are working on a design we have that should be at your dealer in about a month. Contact Antigravity Base for more info Blue Skies Terry Schumacher

It is a friction fit. The bushing on the step ring will hold everything tight, you will not get any shake. If you want put some foam tape on the lid so that when it closes it will squeeze down. Not too much as this will distort the plastic camera. Blue Skies Terry SchumacherQuote

If you need a dril template give me a call or E mail me I will send one no charge Terry Schumacher [email protected]

Send me your address I will send you some for Free. If you want you can get them from McMaster Carr they are about 5 bucks for 100 6-32 x 3/8" Nylon Terry Schumacher

Schumacher makes a nice Friction Fit Case with an option of a cool lens hood designed to protect the Century Optics .3

Just load the software that came with the Camera. Works great and lets you capture Stills

This is a new CX-150 Box I make, Mine is a Friction Fit but you still need about 1/2" for the Hypeye. You could carve into the helmet to clear the plug. Most Bonehead Helmets have 3/4 of an inch before you hit skin Good Luck Terry [email protected]

Terry Schumacher makes several Boxes, One for the CX-100 and one for the CX-110/150. Both are friction fit. They come with the 30mm to 37mm step ring and a lens bushing used to center the lens, It also comes with the hardware for mounting. If my photo comes out you will see the case with an Optional lens hood to fit the Century Optics .3. This lens hood when used replaces the lens bushing used with or without any other lens. Made from High Impact ABS Plastic. It has a smoothe surface as not to rash up the Aircraft. You can get one at most Gear Shops or E Mail Me [email protected]

I make an all ABS box thet requires no bolting the camera in. The Camera fits with no side play. The lens area uses the standard 30 to 37 step ring and if you are jumping a large diameter wide angle lens you can get an optional lens hood shown in this photo. There is a OD groove which the Box closes over holding the lens and hood secure. FYI my hood will aslo fit the Cookie Box.

I make an all ABS box thet requires no bolting the camera in. The Camera fits with no side play. The lens area uses the standard 30 to 37 step ring and if you are jumping a large diameter wide angle lens you can get an optional lens hood shown in this photo. There is a OD groove which the Box closes over holding the lens and hood secure. FYI my hood will aslo fit the Cookie Box.

Hi Spot, Now I know you have this on your mind. How long before the public can Record and Play Back 3-D I know you need a New 3-D TV and a 3-D Blur Ray and the footage recorded I'M guessing from two Cameras. Can you shed any light on this.

This is my new CX-100 Camera Case. I use the Century Optics .3 so I needed a hood that would protect the Lens. You can see a groove around the hood, this fits inside the Face Hole in the camera case. This hood also fits the Cookie Box as well. The case is small, you can leave the strap in tact but it is in the way so I cut it off. There is no bolting of the camera, just slip it in, close the cover and go skydive. Fits the Large Sony and Grey Market battery and I alsh make one just for the stock small Sony Battery. Made from ABS Plastic and comes with a 30mm to 35mm step ring