sundevil777

Some are able to be either an audible or visual altimeter, such as the Alti-2 Neptune series/Atlas.

Something must be getting mixed up I think in the comparison, if those beavers on floats are going to be doing commercial service, they gotta be taking up the same or near the same number of passengers, don’t you think?

My swift plus 175 had a great flare at a 1.26 WL. In my defense I thought it was a 200, as the size is not directly marked on the label, just coded within the serial number as R6 or R4 etc.

Wearing surgical type gloves under thin leather gloves works great. My advice is to put on the surgical gloves on the way to altitude to reduce the likelihood of your hands getting sweaty. That means just wear the leather gloves at first, then add the surgical gloves on the way up. Work it out with your instructors, they won’t like the distraction, so clear it with them first so nobody is surprised.

Does the Ares, like the Viso, show the “tens” of feet digit in free fall (a useless, distracting blur in freefall)? Am I the only one to think it is amazing they continue to show that digit? I think the readability of the L&B products is much worse than the Alti-2 products because the numbers are displayed on a seven segment display type arrangement - straight line segments to display the number. The Alti-2 display (even way back to the Neptune 2) does not have this restriction, allowing a much more quickly readable display. I think the “rounded” font, with higher aspect ratio of each character, and the narrower stroke makes for a huge distinction between the brands.

The "keep an eye out" article on p. 61 of the magazine that showed up today (by Jim Crouch) says that the vast majority of us have brass grommets on the main dbag where bad interaction with rubber bands or tube stows is a real concern. I had thought they were gone long ago.

Forward movement was a goal on some jumps where it seemed to not happen, when you did track, your legs didn’t adjust their position so it was an ineffective track which is common.

Be aware security may demand you open the main and reserve. It does not matter if you have the X-ray cards and USPA letter and all, they can demand it and you can't expect to change their mind. Be aware that carrying your rig around exposed might cause some nervous Nellie to get security involved. No matter how cool it might seem to get on a commercial flight with your rig on your back, it draws unwanted attention and could result in skydivers being treated worse in the future.

Cypres is $53/year more considering the difference in lifetimes.

Comparing cypres to Mars, no time value of money blah blah, $200 more initial cost, + $400 total for 2 inspections/15, = $40/year. This gets the owner a warranty for the 15 years if nothing else. yes, the mars lasts 20 years; so the comparison isn’t quite valid.

My point about getting a used unit applies not just to Cypres. I understand that the used market is tight. Sometimes the per year cost matters less than the "right now" cost. For some, the desire to have a predictable cost (warranty that lasts) is important. I am a fan of the Cypres, but will be considering others when I need to replace mine in few years. The competitors definitely have some advantages, as I have mentioned. I even bought an Astra way back when I returned to jumping after several years away. Fortunately others persuaded me to reconsider and I was able to return it. Back then the only other choice was the original version of the Cypres. The exchange rate at the time allowed me to buy it at perhaps the lowest price ever.

The cypres does have the benefit of being in warranty for the entire lifetime if you get it serviced as recommended. The mars has a 2 year warranty. If the battery on a mars does need to be replaced, even though the mfg says it should last 15 years, it would presumably not be done for free. It is great that it shows the remaining battery life left, and it also shows the pressure the unit is sensing for confirmation to a local barometer. If that pressure check is not within the recommended tolerance, then presumably fixing the unit would not be free. Of course the 15 year warranty of a cypres comes at a cost, and most never need to get their AAD fixed at any time during their life. I think we should acknowledge the trade-off when discussing cost comparisons. Another point worth acknowledging is a Cypres can seem to have no problems at all, no problems during the start-up self-test, and then when SSK does the full series of tests including accuracy/resolution at the fire/no fire limits, high/low temp, vibration, etc it fails to meet the original standards and requires repair before returning to the customer. Does this mean it would have necessarily failed to save your life if needed? No, but it does mean that the mfg is not comfortable with the self test being the only check on the proper function of the unit, and for very good reason - some fail! The self test can't check things to the same extent as can be done at the factory. The self test cannot simulate a jump (simulate the pressures on the transducer) to test the entire system, and cannot test it in harsh environmental conditions. It just is a partial check of the health of the electronics. If cost for an AAD is critical, then getting a used unit is also worth considering. If a used unit is bought at the right price, then the cost/year should be about the same as if buying new. I hear finding used units at the right price is the challenge.

It might be easier than it seems, if you haven't actually tried. Unnecessarily high closing loop tension is common.

You are correct, while I'm holding down on the loop with my thumb, the pin can be taken out and reinserted (there is no reason to want to do that), and of course the pullup cord can be removed with no wear on the loop. I do not "use the pin to pull the loop out a bit...", I just use the pullup cord to get the loop out far enough to allow the pullup to be removed without any friction.

I would be more concerned about losing it from the occasional combat RW encounter. The mag and Grellfab also protrude so far, which makes interference with the mud flaps while looking to the side under canopy worse. I love the https://chinmount.com/ alternative. I haven’t seen anything so low profile, so inexpensive, so well made, and can be used on a Kiss helmet. The ability to dislodge, and break or cutaway is superior to the mag IMO.

I understand your comment about the loop being too long, but no need for concern. It doesn't need to be much past the final grommet for the technique to remove the pullup with zero tension to work.

I was holding the pack tool as you describe, and I still say it is less comfortable than an ordinary pullup. I can agree with you that the spectra cord will wear the closing loop less than a typical pullup used in the normal way, which means withdrawing the pullup when full tension is on the loop/pin. I withdraw my pullup while there is zero tension on the loop, because while the loop is pulled through with extra to spare, I hold my thumb on the loop against the grommet until I get the pullup removed.

I can’t understand the benefit to the pack tool, such a small diameter it hurts more than using a wide pull up cord/ribbon. Even those seem fancy to me, for I grew up using gutted 550 cord. I’ve started using that again the last couple weeks.

The important thing is to call the mfg with your measurements and let them help you decide how to get a fall rate that will allow you to easily play with others. Nobody flies best when having to fly near the upper or lower limit of what they can do.

It may be that the kill line is too long, so it isn't collapsing enough, allowing it to grab enough air to twist. That is the theory anyway that some will propose.

The "affecting the TSO" that was mentioned was only related to the hypothetical case of having someone modify a rig to use a skyhook. You can stop thinking about that completely.

Not just the Jav, it is also available on the Icon and Vortex. Maybe others also, come on people!

I wonder if the L&B Solo has adjustable volume? If we want to go old-school, then of course the original dytter that few have ever seen was definitely not adjustable for volume, and the paralert from Steve Snyder (even less likely to be recognized) was also not. I think the old time-out was fixed volume. Every other type I know of is adjustable.

I think the value of lubricating the inside radius of the 3-ring loop where it contacts the release cable is important and underappreciated. Of course lubing the cable in general is important, but I think a substantial part of the overall force to pull a release cable is due to the drag right at the loop, and applying lube to the loop is a subject worth addressing. The attached pic provides some evidence to support my claim. Mr. Booth used it many years ago in a thread where he advocated the benefits of the traditional, large 3-ring system over mini rings. The different graphs were intended to show how pull force varies with the load at the loop, with the different systems having a different mechanical advantage (and some effect from inconsistent construction affecting mechanical advantage) which results in different loads at the loop. While on the subject of reducing pull force, we might as well touch on what I think is now widely accepted that silicone lube is best instead of some type of oil or other product. I think the gel type silicone grease, such as the cypress loop grease is better than the spray type. Other threads have devoted a lot of discussion about food grade silicone sprays, but the gel makes more sense to me. Please correct me if I am wrong. Perhaps there would be fewer instances of hard pulls and only one side released if lubing the loop were standard practice. I can't remember it being emphasized in all my years. I put the gel grease right on the inside radius of the loop, what do you think?

If the handle is pulled somewhat slowly, or without maximum effort, I think there is a natural tendency to feel the cable moving gradually and then stop when a change in the level of force required to move them occurs. This change of force happens when one side releases first. The length of pull required to release the 2 sides are slightly different - intended to release the side with the RSL last to prevent reserve deployment if a lazy pull is done. The jumper would hopefully recognize that only one side is cutaway and complete the pull. I think it is not reasonable to expect the cable lengths to be just right so as to prevent one side releasing first, therefore the lengths are setup to make the RSL side last. The way to prevent the issue is to apply maximum effort and distance of pull - the expression used to be "punch it". The training to sweep the cables free is I think a recognition that students can't be trusted to punch it all the way out. Every time I've activated a release system, whether capewells or a 3-ring release, I've never had a sense of how much force was actually required because I punched it like my life was on the line.